71M6515H
A Maxim Integrated Products Brand
Energy Meter IC
DATA SHEET
JULY 2011
The SSI timing is shown in Figure 11.
If SSI_CKGATE =1
If 16bit fields
If 32bit fields
If SSI_CKGATE =1
SFR (Output)
SCLK (Output)
SSDATA (Output)
31
30
16
15
1
0
31
30
16
15
1
0
31
1
0
SSI_BEG
SSI_BEG +1
SSI_END
MUX_STATE
Figure 11: SSI Timing ( SSI_FPOL = SSI_RDYPOL = 0)
Fault and Reset Behavior
Reset Mode
When RESETZ is pulled low or when VFLT < V3P3/2, all activity (i.e. sampling of analog signals, CE, generation of digital
outputs) in the chip stops while the analog circuits are active. The exceptions are the oscillator and RTC module, which
continue to run. Additionally, all I/O Register bits are cleared. As long as VFLT > V3P3/2, the internal 2.5V regulator will
continue to provide power to the digital section.
Once initiated, the reset mode will persist until the reset timer times out. This will occur in 4100 cycles of the real time clock
after RESETZ goes high, at which time the 71M6515H will begin executing its preboot and boot sequences.
Power Fault Circuit
The power fault comparator compares the voltage at the VFLT pin to V3P3/2. The comparator output internally enables the
battery backup protection for oscillator, RTC and RAM during the power fail mode.
Temperature Compensation
Voltage Reference
The internal voltage reference of the 71M6515H is calibrated at 25 ° C during device manufacture. The 71M6515H is given
additional temperature-related calibrations which further compensate its ADC gain and allow it to achieve 10PPM/°C over
±60°C temperature range.
Temperature Sensor
The device includes an on-chip temperature sensor for determining the temperature of the bandgap reference. The primary
use of the temperature data is to determine the magnitude of compensation required to offset thermal drift in the system. The
temperature sensor is read once per accumulation interval.
Temperature measurement can be implemented with the following steps:
1)
2)
3)
At a known temperature T N , read the TEMP_RAW register and write the value into TEMP_NOM register.
Read the DELTA_T register at the known temperature. The obtained value should be < ± 0.1°C.
The temperature T (in °C) at any environment can be obtained by reading the DELTA_T register and applying the
following formula:
T = T N +
DELTA _ T
10
Page: 22 of 60
? 2005 ? 2011 Teridian Semiconductor Corporation
1.6
相关PDF资料
71M6521BE-IGTR/F IC ENERGY METER 8K FLASH 64-LQFP
71M6533G-IGTR/F IC ENERGY METER 3PH 100LQFP
71M6543F-IGT/F IC ENERGY METERING
71M6545-IGT/F IC ENERGY METERING
720-10007-00300 CBL D-SUB 9PIN FMAL-25PIN FML 3M
720-10010-00025 CBL DSUB 9PIN FML-25PIN MAL .25M
720-10020-00300 CBL DSUB 9PIN FML-9PIN MALE 3M
720-10021-00300 CBL DSUB 9PIN FML-9PIN FEMAL 3M
相关代理商/技术参数
71M6515H-IGTR 制造商:Maxim Integrated Products 功能描述:71M6515H-IGT - T/REEL - Tape and Reel 制造商:Maxim Integrated Products 功能描述:Metering Systems on a Chip - SoC Energy Meter IC
71M6515H-IGTR/F 功能描述:计量片上系统 - SoC Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6515H-IGTW/F 功能描述:计量片上系统 - SoC Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6515H-IGTW1 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Up to 10ppmC precision ultra-stable voltage reference Digital temperature compensation
71M6515H-IGTWR1 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Up to 10ppmC precision ultra-stable voltage reference Digital temperature compensation
71M6521BE 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Energy Meter IC
71M6521BE-DB 制造商:Maxim Integrated Products 功能描述:Development Boards & Kits - 8051 71M6521BE Demo Brd
71M6521BE-IGT/F 功能描述:计量片上系统 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel